Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 176

background image

Safety instructions

5

1

Safety instructions

1.1

Designated use

Topcal S CPC310 is a fully automated measuring, cleaning and calibration system for pH and redox
measurement.
The system is fully equipped with power supply cables and hose systems.
Topcal S CPC310 can be operated using the handheld terminal DXR375 or at a PC by means of the
FieldCare program via a HART

®

modem, e.g. Commubox FXA191.

The system is particularly suitable for use in the following areas:
• Chemical process systems
• Pharmaceuticals
• Foodstuff industry
• Water treatment and monitoring
• Wastewater treatment
• Sewage treatment plants
• Chemical pulp and paper industry

Topcal S CPC310 is suitable for use in hazardous atmospheres.

Any use other than that described here compromises the safety of persons and the entire measuring
system and is, therefore, not permitted.
The manufacturer accepts no liability for damage resulting from incorrect use or use other than that
designated.

1.2

Installation, commissioning and operation

Note the following points:
• Installation, commissioning, operation and maintenance of the measuring system must be carried

out exclusively by specially trained technical personnel.
The personnel must be authorized to perform such work by the system operator.

• The electrical connection may only be established by an electrical technician.
• Technical personnel must have read and understood these Operating Instructions and must

adhere to them.

• Before commissioning the entire measuring point, check all the connections for correctness.

Ensure that electrical cables and hose connections are not damaged.

• Do not commission damaged products. Protect them against inadvertent commissioning. Mark

the damaged product as defective.

• Faults at the measuring point may only be rectified by authorized and specially trained personnel.
• If faults cannot be rectified, you must take the products out of operation and protect them against

inadvertent commissioning.

• Repairs not described in these Operating Instructions may only be carried out directly at the

manufacturer's or by the service organization.

1.3

Operational safety

The system is designed to meet state-of-the-art safety requirements, has been tested and left the
factory in a condition in which it is safe to operate. The applicable regulations and European
standards have been taken into consideration.

As the user, you are responsible for ensuring the following safety regulations are observed:
• Installation regulations
• Local standards and regulations

«
...
3
4
5
6
7
...
»

Содержание Topcal S CPC310

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Topcal S CPC310

Бренд: Kane Страницы: 19

Goldmann AT 870

Бренд: Haag-Streit Страницы: 20

Бренд: X-Rite Страницы: 45

Бренд: X-Rite Страницы: 22

Бренд: YOSensi Страницы: 26

Бренд: YOSensi Страницы: 26

Бренд: Danfoss Страницы: 80

Бренд: Omega Страницы: 31

Бренд: LumaSense Страницы: 23

Бренд: Jaquet Страницы: 27

Бренд: Kirby Morgan Страницы: 101

Бренд: BASI Страницы: 69

Бренд: Major tech Страницы: 20

Бренд: Milkotester Страницы: 44

Бренд: National Instruments Страницы: 24

Бренд: Heyuan Intelligence Страницы: 14

Бренд: IFM Страницы: 13

Бренд: BAPI Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды