Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 176

background image

Maintenance

122

8

Maintenance

Take all the necessary measures in good time to ensure the operational safety and reliability of the
entire measuring system.

Measuring point maintenance comprises:
• Calibration (see "Calibration" section)
• Cleaning the transmitter, assembly and sensor
• Inspecting cables and connections
• Maintenance of the control unit

#

Warning!
• When performing work on the device, take possible effects on the process control system or the

process itself into account.

• If you have to remove the sensor for servicing or calibration work, pay attention to the hazards

caused by pressure, temperature and contamination.

• The control unit and process retractable assembly work with compressed air and pressurized

water. Disconnect the air and water supply before working on couplings, valves or pressure
switches!

• De-energize the device before you open it.

If work has to be performed while the unit is energized, it may only be carried out by an
electrician.

• Power can be supplied to switching contacts by separate circuits. Also de-energize these circuits

before you work on the terminals.

• Electronic components are sensitive to electrostatic discharge. Personal protective measures such

as permanent grounding with a wrist strap are necessary.

• For your own safety, always use genuine spare parts. The function, accuracy and reliability after

repair work are guaranteed with genuine parts.

!

Note!
Please contact your sales center if you have any questions.

8.1

Maintenance of the overall measuring point

8.1.1

Cleaning the transmitter

Clean the front of the housing with usual commercial cleaning agents.

In accordance with DIN 42 115, the front is resistant to the following:
• Isopropyl alcohol
• Diluted acids (max. 3%)
• Diluted bases (max. 5%)
• Ester
• Hydrocarbons
• Ketones
• Household cleaners

"

Caution!
When cleaning, never use:
• Concentrated mineral acids or bases
• Benzyl alcohol
• Methylene chloride
• High-pressure steam

8.1.2

Cleaning the sensors

Cleaning the sensor constitutes an integral part of the Topcal S system; thus, additional or external
sensor cleaning is normally not necessary. However, before monitoring the sensor, advance external
cleaning may be necessary.

"

Caution!
Set the service switch to "Service", to hold the assembly securely in the Service position.

«
...
120
121
122
123
124
...
»

Содержание Topcal S CPC310

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Topcal S CPC310

Бренд: AccuMASTER Страницы: 2

Бренд: Oceanic Страницы: 17

Бренд: Omicron Lab Страницы: 33

Бренд: Omicron Lab Страницы: 21

Бренд: Omicron Lab Страницы: 22

Бренд: Vectornav Страницы: 114

Бренд: Parkside Страницы: 94

Бренд: Xylem Страницы: 19

Бренд: YOKOGAWA Страницы: 53

Бренд: Teledyne Analytical Instruments Страницы: 107

Бренд: Shimpo Страницы: 68

Бренд: JENCO Страницы: 13

Бренд: UEi Страницы: 5

Бренд: C.R. Laurence Страницы: 4

Бренд: Neogen Страницы: 9

DigiFlow 6710M-22

Бренд: Savant Страницы: 3

Бренд: Velleman Страницы: 38

Бренд: Rebel Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды