Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 104

Страница: 104 / 176

Commissioning

104

7.6.18

Manual operation

To call the menu, select:
"

> Specialist > Manual operation"

Copy day

Select day

Options
• Tuesday
• Wednesday
• Thursday

...

Factory setting

Tuesday

Select the day to which you want to copy the
day previously selected (e.g. Monday).

Note!

Danger of data loss. When copying one day to
another, the cleaning programs of the target day
are overwritten.

Interval program

Select program
Enter interval

Activation and subsequent entry
• Program

– Clean
– User prog.

• Interval

0 ... 36000 s

Factory setting

Program: Clean
Interval: 3600 s

Program:

Select the program that should be

started at the defined intervals.

Interval:

Enter the time that should elapse

between the end of one program cycle and the
start of the next program cycle.

Change name

0 ... 9; A ... Z

You can enter any name for the interval
program.

Function

Options

Info

Manual operation

Options
• Hold
• Topcal
• Chemoclean

You canactivate a manual hold and start the
Chemoclean or Topcal program.
The settings you make here are only active in
this menu. Nothing is saved when you leave.
You exit the manual operation menu with

Hold

Activate hold

Options
• Hold on
• Hold off

Factory setting

Hold off

Activate/deactivate the HOLD. The "HOLD"
function freezes the current outputs as soon
cleaning/calibration is undertaken.

Note!

If the controller function is set to current output
2, this output obeys the defined "controller
hold" (see also "Set up 1 - Hold" section).

Topcal

Note

Automatic off
Cleaning trigger off
Ext. control off

Displays the status of the system.

Select function

Options
• Retract assembly
• Start program
• Stop program

You can move the assembly manually or
stop/start a program.

Retract assembly

Select position

Options
• Assembly service
• Assembly measuring

Select the position to which the assembly
should move.

Function

Options

Info

pH 7.00

Hold

Param

Manual operation

Hold

Topcal
Chemoclean

Edit [¯]

Next [E]

Содержание Topcal S CPC310

















































































































































































Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды

Endress+Hauser Topcal S CPC310, Руководство по эксплуатации

Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды