Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 59

Страница: 59 / 114

Operating the Analyzer

Operator’s Manual

–

If the

4-20 mA Val Action

parameter is set to “1”, the 4-20 mA signal will

output validation measurements and the appropriate relay (Val #1 Active or Val

#2 Active) will be activated. If the concentration measured does not fall within

the allowable limits during an automatic or semi-automatic validation (see

“Validation Allowance”

on page 2-33), the

Validation Fail Alarm

relay will

activate. Once activated, the

Validation Fail Alarm

must be manually

canceled (see

“Cancel Val Alarms”

on page 2-19). Initiating a new

automatic, semi-automatic or manual validation will clear the

Validation Fail

Alarm

so that the new validation can determine its state.

Calibrating the Analyzer

Calibrating the analyzer is typically not required under normal circumstances.

SpectraSensors calibrates each analyzer to a National Institute of Standards

and Technology (NIST) traceable standard before shipping the unit to the end

user. Because SpectraSensors analyzers use a non-contact form of

measurement, they are relatively insensitive to contamination, are quite

rugged and virtually maintenance free ensuring years of reliable service.

Switching Stream Compositions

Some analyzers may be configured with dual stream compositions. To switch

between the two calibration methods, use the analyzer keypad to change the

system programming. Refer to the following steps.

To measure Stream 1

From the analyzer keypad, press the

key followed by the

key to

enter the Set Parameter Mode (

Mode 2

Enter the password (

1688

Scroll through the parameters until the parameter, “Background to

Use,” displays.

Press

(Prcs) and the ENTER key.

Press the

key followed by the

key to begin measurement.

SpectraSensors recommends validating the analyzer using only

the analyte mixed in the validation gas specified on the analyzer

calibration report. A bottle of test gas with a certified

concentration representing 50% of full scale (for single validation

systems) or bottles representing 20% and 80% of full scale (for

dual validation systems) are recommended.

When procuring a gas standard, make sure the background gas is

that specified or a mix that closely resembles the contents of the

process stream and have the gas standard certified to better than

the specified precision of the analyzer, if possible.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды