Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 51

Страница: 51 / 114

Operating the Analyzer

Operator’s Manual

–

•

If using a permeation-based single validation system, then a new

RATA Multiplier

is calculated and the

RATA Offset

is left at its

previous value.

•

If using a dual validation system, then both a new

RATA Multiplier

and

RATA Offset

are calculated.

To adjust the analyzer reading

Validate the analyzer using one or two concentration standards

(refer to

“Validating the Analyzer”

on page 2-40).

Enter

Mode 2

by pressing the

key followed by the

key. The LCD

prompts for a numeric password.

Enter the user password (

3142

) on the keypad, then press the

key.

View the newly calculated

RATA Multiplier

and

RATA Offset

parameters from the

Update RATA

parameter or calculate the

RATA

Multiplier

and/or

RATA Offset

parameter(s) manually using

the equations above.

Follow the procedure under

“To change parameters in Mode 2”

on page 2-15 to enter the new values.

Confirm the new values by re-measuring the bottle(s) of test gas.

SpectraSensors recommends validating the analyzer using only

the analyte mixed in the validation gas specified on the analyzer

calibration certificate. A bottle of test gas with certified

concentrations of approximately 20% and 80% of full scale are

recommended for a two point validation. For a single point

validation, a bottle with a certified concentration of approximately

50% of full scale should be used.

When procuring a gas standard, make sure the background gas is

that specified or a mix that closely resembles the contents of the

process stream and have the gas standard certified to better than

the specified precision of the analyzer, if possible.

RATA values are also applied to the validation measurements. If

RATA free validation values are required, the RATA parameter

must be disabled before running the validation.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды