Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 48

Страница: 48 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

Enter the required value.

Val Interval

The

Val Interval

parameter sets the number of days between autovalidation

cycles. The next scheduled validation cycle would occur in

Val Interval

days

at the

Val Start Time

. Enter the required value.

Val Perm Constant Kp

The

Val Perm Constant Kp

parameter is used for permeation validation

devices and defines the system constant that is determined at the factory

during calibration. Using the system constant, the permeation device can be

replaced with another permeation device with a different permeation rate, and

the correct new permeation concentration is calculated by the analyzer

software. The system constant K

will be constant over the life of the analyzer

provided the temperature, sample flow rate and pressure of the system are not

changed from the factory settings. If the system constant needs to be reset,

refer to

“Setting the Kp Value”

in the Hardware Manual for details on

recalculating the system constant.

Val Perm Rate Rp

The

Val Perm Rate Rp

parameter is used for permeation validation devices

and defines the permeation rate in ng/min referenced on the permeation

device certification. This certification is valid for a period of one (1) year.

However, the permeation device may be used longer than that period if a

factory certified validation concentration is not required. When the validation

Validation Wait Time

Enter a value (secs)

Val Interval

Enter a value (days)

Val Perm Constant Kp

0.24

0:Off >0:System Cons

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды