Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 16

Страница: 16 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

The system goes through an initialization period while showing the

firmware version on the bottom line until the LCD displays the

Normal Mode screen.

Enable

Peak Tracking

following the procedure outlined in

“To

change parameters in Mode 2”

on page 2-15.

After initialization and establishment of reference spectra, the LCD

displays four lines, the third of which is blank.

The measurements displayed are:

•

ANA

: Refers to the concentration in the sample cell (in units) of

the analyte/component selected in

Mode 2

•

: Pressure in the sample cell in units selected in

Mode 2

•

: Temperature in the sample cell in units selected in

Mode 2

Continuous updates of the measurement parameters displaying on

the LCD indicates that the analyzer is operating normally.

Powering Down the Analyzer

It may be necessary to power down the analyzer for problem solving or

maintenance reasons. An approved switch or circuit breaker rated for 15 amps

should have been installed and clearly marked as the disconnecting device for

the analyzer.

For systems with heated enclosures, a

Temperature too Low

Temperature too High

fault will activate the

General Fault

Alarm

when the enclosure temperature is more than 5 °C above

or below the specified temperature. Once the enclosure has

reached the specified temperature, reset the

General Fault

Alarm

(see

“To change parameters in Mode 2”

on page 2-15).

Definitions for the acronyms displayed on the LCD are given in the

section

“Modes Defined”

on page 2-5.

ANA: 4.0256ppmv

P: 954.4mb T: 76.1F

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды