Endress+Hauser Prosonic M FMU42 Скачать руководство пользователя страница 35

Страница: 35 / 52

Prosonic M FMU42 HART

Diagnostics and troubleshooting

Hauser

A512 = Recording of mapping

Alarm ends after a few seconds

A521 = New sensor type identified

Perform a reset

A671 = Linearization not complete, not usable

Perform the basic setup

E281 = Wire breakage at temperature sensor

Replace the sensor and/or electronics

E641 = No usable echo

Check the basic setup

E651 = Level in safety distance, risk of overspill

• The error disappears as soon as the level is no longer in the safety distance

• Acknowledge alarm

Safety settings (01)

function group →

Acknowledge alarm (017)

function

E661 = Sensor temperature too high
W103 = Initializing

If the message does not disappear, replace the electronics

W153 = Initializing

• Wait a few seconds

• If the error remains active, switch the voltage off/on

W601 = Linearization curve not monotone

Correct the table, enter a table that increases monotonically

W611 = Less than 2 linearization points

Enter more value pairs

W621 = Simulation on

Switch off the simulation mode,

Output (06)

function group →

Simulation (065)

function

W681 = Current out of range

• Perform the basic setup

• Check linearization

W691 = Noise filling

10.5 Application errors

Error:

Measured value (000)

incorrect, measured

distance (008)

correct.

Example:

100%

t →

D (008)

A0038459

Expected result

Error occurred

1. Check

Empty calibration (005)

and

Full calibration (006)

and correct.

Содержание Prosonic M FMU42





















































Результаты поиска

Содержание Prosonic M FMU42

Отзывы:

Похожие инструкции для Prosonic M FMU42

Бренды по названию

Популярные бренды

Endress+Hauser Prosonic M FMU42, Руководство по эксплуатации

Результаты поиска

Содержание Prosonic M FMU42

Отзывы:

Похожие инструкции для Prosonic M FMU42

Бренды по названию

Популярные бренды