Endress+Hauser Prosonic M FMU40 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 60

background image

Prosonic M FMU40 HART

Mounting

Hauser

15

F

E

BD

SD

A0038238

 12

Parameters for the correct operation of the device

BD Blocking distance
SD Safety distance
E

Empty calibration

F

Measuring span

Mounting nozzle

L

D

A0038239

 13

Definition of nozzle length L and nozzle diameter D

D

Nozzle diameter

L

Nozzle length

Conditions

• Smooth interior surfaces in pipe nozzle

Remove any edges or welded joints and burr on the inside of the tank side nozzle end

• To minimize disturbing factors: nozzle with an angled socket edge (ideally 45 °)

• Observe maximum nozzle length

Maximum nozzle length

Diameter with maximum nozzle length

• DN50/2": 80 mm (3.15 in)

• DN80/3": 240 mm (9.45 in)

• DN100/4": 300 mm (11.8 in)

• DN150/6": 400 mm (15.7 in)

• DN200/8": 400 mm (15.7 in)

• DN250/10": 400 mm (15.7 in)

• DN300/12": 400 mm (15.7 in)

«
...
13
14
15
16
17
...
»

Содержание Prosonic M FMU40





























































Отзывы:

Нет отзывов

Похожие инструкции для Prosonic M FMU40

Бренд: ABB Страницы: 20

Бренд: Utilitech Страницы: 2

Бренд: Omer Страницы: 2

Бренд: Hach Страницы: 145

Бренд: Hach Страницы: 358

Polymetron 9582sc

Бренд: Hach Страницы: 280

Бренд: HACH LANGE Страницы: 15

Бренд: SAGEMCOM Страницы: 33

Бренд: +GF+ Страницы: 64

Бренд: +GF+ Страницы: 12

Бренд: +GF+ Страницы: 48

Бренд: Teledyne Analytical Instruments Страницы: 107

Бренд: HANSA-FLEX Страницы: 23

Бренд: ASCEL Electronic Страницы: 64

Бренд: Tektronix Страницы: 116

Бренд: Magnetrol Страницы: 48

Бренд: Fluke Страницы: 5

Бренд: PCE Health and Fitness Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды