Endress+Hauser prosonic flow 92 Скачать руководство пользователя страница 33

Страница: 33 / 98

Prosonic Flow 92

4 Wiring

Hauser

4.3

Potential equalisation

Special measures for potential equalisation are not necessary.

4.4

Degree of protection

The measuring system fulfills all the requirements for IP 50 degree of protection.

• Flow measuring transmitter Prosonic Flow 92:

IP 50

• Flow measuring sensors Prosonic Flow W, P:

– Sensor in IP 54, if BNC adapter and BNC cable fully engaged.
– Sensor in IP 67/68 (NEMA 4X / NEMA 6P), if Prosonic Flow sensor cable fully

engaged.

Caution!
The BNC adapter resp. the cable connection defines the W (P) sensors specification for
the degree of protection (IP 54).

• Flow measuring sensors Prosonic Flow U:

IP 54

4.5

Post-connection check

Perform the following checks after completing electrical installation of the measuring
device:

Device condition and specifications

Notes

Are cables or the device damaged?

visual inspection

Electrical connection

Notes

Does the supply voltage match the specifications on the nameplate of
the power adapter?

100...240 V AC (47...63 Hz)

Do the cables comply with the specifications?

see Page 27

Cables correctly segregated by type, without loops and crossovers?

visual inspection

Are the power supply and sensor cables correctly connected?

see Page 27, 28

Содержание prosonic flow 92



































































































Результаты поиска

Содержание prosonic flow 92

Отзывы:

Endress+Hauser prosonic flow 92, Руководство по эксплуатации, Страница: 33 / 98

Результаты поиска

Содержание prosonic flow 92

Отзывы: