Endress+Hauser Proline t-mass 65 PROFIBUS DP Скачать руководство пользователя страница 25

Страница: 25 / 106

Proline t-mass 65 PROFIBUS DP

Installation

3.3

Installation instructions

3.3.1

Turning the transmitter housing

Turning the aluminium field housing

Warning!
The rotating mechanism for devices for hazardous areas Zone 1 (ATEX) or Class I Div. 1 (FM/CSA)
is different to that described here. The procedure for turning these housings is described in the
Ex-specific documentation.

Loosen the two securing screws.

Turn the bayonet catch as far as it will go.

Carefully lift the transmitter housing as far as it will go.

Turn the transmitter housing to the desired position (max. 2 x 90° in either direction).

Lower the housing into position and re-engage the bayonet catch.

Retighten the two securing screws (only Hauser screws to be used).

a0004302

Fig. 16:

Turning the transmitter housing (aluminium field housing)

3.3.2

Installing the wall-mount transmitter housing

There are various ways of installing the wall-mount transmitter housing:

• Mounted directly on the wall

→

Page 26

• Installation in control panel

→

Page 26 (separate mounting set, accessories

→

Page 70)

• Pipe mounting

→

Page 27 (separate mounting set, accessories

→

Page 70)

Caution!
• Make sure that ambient temperature does not go beyond the permissible range of

– 20 °C to +60 °C (–2 °F to +140 °F), optional – 40 °C to +60 °C (–40 °F to +140 °F).
Install the device in a shaded location. Avoid direct sunlight.

• Always install the wall-mount housing in such a way that the cable entries are pointing down.

Содержание Proline t-mass 65 PROFIBUS DP











































































































Результаты поиска

Содержание Proline t-mass 65 PROFIBUS DP

Отзывы:

Похожие инструкции для Proline t-mass 65 PROFIBUS DP

Бренды по названию

Популярные бренды

Endress+Hauser Proline t-mass 65 PROFIBUS DP, Руководство по эксплуатации

Результаты поиска

Содержание Proline t-mass 65 PROFIBUS DP

Отзывы:

Похожие инструкции для Proline t-mass 65 PROFIBUS DP

Бренды по названию

Популярные бренды