Endress+Hauser Proline Prowirl F 200 Скачать руководство пользователя страница 146

Страница: 146 / 224

Diagnostics and troubleshooting

Proline Prowirl F 200 PROFIBUS PA

146

Hauser

Diagnostic information

Diagnostic code

Diagnostic

behavior

Status signal

Diagnostic

number

Short text

↓

Example

A0013962

A0013956

261

Electronics

modules

NAMUR

NE 107

3-digit number

12.3.2 Calling up remedy information

Remedy information is provided for every diagnostic event to ensure that problems can be

rectified quickly:

• On the home page

Remedy information is displayed in a separate field below the diagnostics information.

• In the

Diagnostics

Remedy information can be called up in the working area of the user interface.

The user is in the

Diagnostics

menu.

1. Call up the desired parameter.
2. On the right in the working area, mouse over the parameter.

 A tool tip with remedy information for the diagnostic event appears.

12.4 Adapting the diagnostic information

12.4.1 Adapting the diagnostic behavior

Each item of diagnostic information is assigned a specific diagnostic behavior at the

factory. The user can change this assignment for specific diagnostic information in the

Diagnostic behavior

submenu.

Diagnostic behavior in accordance with Specification PROFIBUS PA Profile 3.02,

Condensed Status.

Expert → System → Diagnostic handling → Diagnostic behavior

0658-1

Diagnostic no.442

/ ../Diagn. behavior

Diagnostic no.443

Warning

A0019179-EN

Содержание Proline Prowirl F 200

































































































































































































































Результаты поиска

Содержание Proline Prowirl F 200

Отзывы:

Похожие инструкции для Proline Prowirl F 200

Бренды по названию

Популярные бренды

Endress+Hauser Proline Prowirl F 200, Руководство по эксплуатации

Результаты поиска

Содержание Proline Prowirl F 200

Отзывы:

Похожие инструкции для Proline Prowirl F 200

Бренды по названию

Популярные бренды