Endress+Hauser Proline Promag W 400 HART Скачать руководство пользователя страница 57

Страница: 57 / 198

Proline Promag W 400 HART

Operation options

Hauser

Display area

In the display area, each measured value is prefaced by certain symbol types for further

description:

Measured variable

Measurement channel

number

Diagnostic behavior

↓

Example

Appears only if a diagnostics
event is present for this
measured variable.

Measured values

Symbol

Meaning

Volume flow

Conductivity

Mass flow

Totalizer



The measurement channel number indicates which of the three totalizers is
displayed.

Output



The measurement channel number indicates which of the outputs is displayed.

Status input

Measurement channel numbers

Symbol

Meaning

Measurement channel 1 to 4

The measurement channel number is displayed only if more than one channel is present for the same measured
variable type (e.g. Totalizer 1 to 3).

Diagnostic behavior

The diagnostic behavior pertains to a diagnostic event that is relevant to the displayed measured variable.
For information on the symbols →  126

The number and display format of the measured values can be configured via the

Format display

parameter (→  95).

Содержание Proline Promag W 400 HART







































































































































































































Результаты поиска

Содержание Proline Promag W 400 HART

Отзывы:

Похожие инструкции для Proline Promag W 400 HART

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag W 400 HART, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag W 400 HART

Отзывы:

Похожие инструкции для Proline Promag W 400 HART

Бренды по названию

Популярные бренды