Endress+Hauser Proline Promag W 400 HART Скачать руководство пользователя страница 38

Страница: 38 / 198

Electrical connection

Proline Promag W 400 HART

Hauser

Electrical connection

NOTICE

The measuring device does not have an internal circuit breaker.

‣

For this reason, assign the measuring device a switch or power-circuit breaker so that

the power supply line can be easily disconnected from the mains.

‣

Although the measuring device is equipped with a fuse, additional overcurrent

protection (maximum 16 A) should be integrated into the system installation.

7.1

Connection conditions

7.1.1

Requirements for connecting cable

The connecting cables provided by the customer must fulfill the following requirements.

Electrical safety

In accordance with applicable federal/national regulations.

Permitted temperature range

Minimum requirement: cable temperature range ≥ ambient tempe20 K

Power supply cable

Standard installation cable is sufficient.

Signal cable

Current output 0/4 to 20 mA

Standard installation cable is sufficient.

Current output 4 to 20 mA HART

A shielded cable is recommended. Observe grounding concept of the plant.

Pulse/frequency/switch output

Standard installation cable is sufficient.

Status input

Standard installation cable is sufficient.

Connecting cable for remote version

Electrode cable

Standard cable

3 ×0.38 mm

(20 AWG) with common, braided copper shield (

9.5 mm

(0.37 in)) and individual shielded cores

Cable for empty pipe
detection (EPD)

4 ×0.38 mm

(20 AWG) with common, braided copper shield (

9.5 mm

(0.37 in)) and individual shielded cores

Conductor resistance

≤50 Ω/km (0.015 Ω/ft)

Capacitance: core/shield

≤420 pF/m (128 pF/ft)

Operating temperature

–20 to +80 °C (–68 to +176 °F)

Содержание Proline Promag W 400 HART







































































































































































































Результаты поиска

Содержание Proline Promag W 400 HART

Отзывы:

Похожие инструкции для Proline Promag W 400 HART

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag W 400 HART, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag W 400 HART

Отзывы:

Похожие инструкции для Proline Promag W 400 HART

Бренды по названию

Популярные бренды