manualshive.com logo in svg

Endress+Hauser Proline Promag 55, Руководство по эксплуатации

Endress+Hauser Proline Promag 55 - измеритель потока жидкостей высокой точности. Получите подробное руководство по эксплуатации с помощью бесплатного руководства по эксплуатации на manualshive.com. Загрузите руководство по эксплуатации прямо сейчас, чтобы максимально эффективно использовать этот продукт.

Поделиться
Скачать
background image

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

77

The CHANNEL parameter in the Analog Input function block is used to assign which process 
variable is read in and processed in the downstream Analog Input function block:

• Process variable Calculated Mass Flow 

→

 CHANNEL 1 (Analog Input function block)

• Process variable Volume Flow

→

 CHANNEL 2 (Analog Input function block)

• Process variable Totalizer 1 

→

 CHANNEL 7 (Analog Input function block)

• Process variable Totalizer 2 

→

 CHANNEL 8 (Analog Input function block)

• Process variable Totalizer 3 

→

 CHANNEL 9 (Analog Input function block)

3.2.2

Selecting the operating mode

The operation mode is set by means of the MODE_BLK parameter group. The Transducer Blocks 
support the following operation modes:

• AUTO (automatic mode)
• OOS (out of service)

!

Note!
• The block status OOS is also shown via the parameter BLOCK_ERR. In operating mode OOS, if 

write protection is not enabled and the access code is entered, you can access all the write 
parameters without restriction.

• The following applies for the "Flow" and "Totalizer" Transducer Blocks: With the "OOS" operating 

mode, the process variables are updated but the status of the output value OUT (AI Block) changes 
to "BAD".

• If problems occur during the configuration of the function blocks 

→

 see Operating Instructions 

for  Proline Promag 55 FOUNDATION Fieldbus (BA126D), "Troubleshooting" section. 

3.2.3

Alarm detection and processing

The Transducer Blocks do not generate any process alarms. The status of the process variables is 
evaluated in the downstream Analog Input function blocks. If the Analog Input function block does 
not receive an input value that can be evaluated from the "Flow" or "Totalizer" Transducer Blocks, 
then a process alarm is generated. This process alarm is displayed in the BLOCK_ERR parameter of 
the Analog Input function block (BLOCK_ERR = Input Failure).

The parameter BLOCK_ERR of the Transducer Blocks displays the device error that produced the 
input value that could not be evaluated and thus triggered the process alarm in the Analog Input 
function block.

In addition, the active device error is displayed via the "Diagnosis" Transducer Block in the 
"Diagnosis - Act.Sys. Condition" parameter (

  →  

Page 90). 

For further information on rectifying errors 

→ 

see

 

 Operating Instructions for Proline Promag 55 

FOUNDATION Fieldbus (BA126D), "Troubleshooting" section.

3.2.4

Diagnosis

The status of the device is displayed via the following parameters specified in the FOUNDATION 
Fieldbus specification:

• BLOCK_ERR 
• Transducer Error 

More detailed information on the current device status is displayed via the "Diagnosis" Transducer 
Block in the manufacturer-specific parameter "Diag. - Act.Sys.Condition" (

  →  

Page 90).

For further information on rectifying errors 

→

see Operating Instructions for Proline Promag 55 

FOUNDATION Fieldbus (BA126D), "Troubleshooting" section.

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

JANE MICRO Quick Start Manual preview
MICRO
Бренд: JANE Страницы: 6
Acclima TDR Series User Manual preview
TDR Series
Бренд: Acclima Страницы: 16
Access One WVD100 Quick Reference Manual preview
WVD100
Бренд: Access One Страницы: 2
Accelleran E1000 Series Safety And Installation Instructions Manual preview
E1000 Series
Бренд: Accelleran Страницы: 19
E-max Express Quick Start Manuals preview
Express
Бренд: E-max Страницы: 4
Dacor EF36LNFSS Installation Instructions preview
EF36LNFSS
Бренд: Dacor Страницы: 4
Gamko FK User Manual preview
FK
Бренд: Gamko Страницы: 32
Magellan CYCLO 315 Series User Manual preview
CYCLO 315 Series
Бренд: Magellan Страницы: 39
MadStad Engineering MadStad Installation Instruction preview
MadStad
Бренд: MadStad Engineering Страницы: 2
NENKO Sleeptrainer Palm the penguin Manual preview
Sleeptrainer Palm the penguin
Бренд: NENKO Страницы: 4
Solight DY10GSM Quick Start Manual preview
DY10GSM
Бренд: Solight Страницы: 2
Berkefeld 7564 20 Series Operation And Assembly Instructions preview
7564 20 Series
Бренд: Berkefeld Страницы: 12
DOMUS LINE IR 2.0 12-24Vdc Installation Manual preview
IR 2.0 12-24Vdc
Бренд: DOMUS LINE Страницы: 9
Dometic GROUP DRS2 Installation And Operating Manual preview
DRS2
Бренд: Dometic GROUP Страницы: 20
Ikan PBK-A-X Quick Start Manual preview
PBK-A-X
Бренд: Ikan Страницы: 2
GROTHE CALIMA 800 Installation And Operating Instructions Manual preview
CALIMA 800
Бренд: GROTHE Страницы: 36
Compass 02106 Manual preview
02106
Бренд: Compass Страницы: 16
Cygolite Expilion Operation Manual preview
Expilion
Бренд: Cygolite Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды