Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 41

Страница: 41 / 130

Device Functions Proline Promag 55 FOUNDATION Fieldbus

7 Block BASIC FUNCTION

Hauser

7.1

Group FOUNDATION FIELDBUS

7.1.1

Function group CONFIGURATION

BASIC FUNCTION

⇒

FOUNDATION FIELDBUS GGA

⇒

CONFIGURATION

620

Function description

BASIC FUNCTION

→

FOUNDATION FIELDBUS

→

CONFIGURATION

WRITE PROTECT
(6200)

Use this function to check whether the measuring device can be write-accessed via the
fieldbus.

User interface:

OFF

→

Write access via FOUNDATION Fieldbus possible

→

Write access via FOUNDATION Fieldbus not possible

Factory setting:

OFF

Note!

Hardware write protection is activated and deactivated by means of a jumper on the I/O
board (

→

see Operating Instructions for Proline Promag 55 FOUNDATION Fieldbus).

SIMULATION
(6201)

Use this function to check whether a simulation in the Analog Input or Discrete Output
function block is possible.

User interface:

OFF

→

Simulation in the Analog Input and Discrete Output function block is

not

possible.
ON

→

Simulation in the Analog Input and Discrete Output function block is possible

Factory setting:

Note!

• The simulation mode is enabled and disabled by means of a jumper on the I/O board

(

→

see also Operating Instructions for Proline Promag 55 FOUNDATION Fieldbus).

• The status of the simulation mode is also shown in the parameter BLOCK_ERR of the

Resource Block.

DEVICE PD-TAG
(6203)

Use this function to enter a tag name for the measuring device.

User input:

Max. 32-character text, permissible: A-Z, 0-9, +,–, punctuation marks

Factory setting:

E+H_PROMAG_55_XXXXXXXXXXX

Содержание Proline Promag 55



































































































































Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 55, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды