Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 39

Страница: 39 / 130

Device Functions Proline Promag 55 FOUNDATION Fieldbus

6 Block TOTALIZER

Hauser

6.2

Group HANDLING TOTALIZER

TOTALIZER

⇒

TOTALIZER 1

DAA

⇓

TOTALIZER 2

DAB

⇓

TOTALIZER 3

DAC

⇓

HANDLING TOTALIZER

DJA

⇒

Handling totalizer functions

Function description

TOTALIZER

→

HANDLING TOTALIZER

→

Handling totalizer functions

RESET ALL TOTALIZERS
(3800)

Use this function to reset the totals (including all overflows) of the Totalizers (1 to 3) to
zero (= RESET).

Options:

NO
YES

Factory setting:

FAILSAFE ALL TOT
(3801)

Use this function to define the common response of all Totalizers (1 to 3) in case of error.

Options:

STOP
The totalizer is paused until the fault is rectified.

ACTUAL VALUE
The totalizers continue to count based on the actual flow measured value. The fault is
ignored .

HOLD VALUE
The totalizers continue to count the flow based on the last valid flow value (before the
fault occurred).

Factory setting:

STOP

Содержание Proline Promag 55



































































































































Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 55, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды