Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 14

Страница: 14 / 130

3 Block MEASURED VARIABLES

Device Functions Proline Promag 55 FOUNDATION Fieldbus

Hauser

3.3

Group

SPECIAL UNITS

3.3.1

Function group DENSITY PARAMETER

MEASURED

VARIABLES

⇒

MEASURING VALUES

AAA

⇓

SYSTEM UNITS

ACA

⇓

SPECIAL UNITS

AEA

⇒

DENSITY PARAMETER

070

Function description

MEASURED VARIABLES

→

SPECIAL UNITS

→

DENSITY PARAMETER

Use this function group to calculate a mass flow from a volume flow.

Note!

It is advisable to enter the density factor at process temperature for calculating the mass flow without compensating for
thermal expansion.

Example of calculated mass flow

without

compensation for thermal expansion of the fluid:

= 1 [dm

/h]

⋅

0.900 [kg/l] = 0.900 [kg/h] (mass flow at 20 °C)

= 1 [dm

/h]

⋅

0.783 [kg/l] = 0.783 [kg/h] (mass flow at 150 °C)

= Mass flow [kg/h]

= Volume flow = 1 [dm

/h]

= Density factor [kg/ l], see DENSITY VALUE function (0700)

DENSITY
VALUE (0700)

Use this function to enter a density value preferably at process temperature (or at
reference temperature). This density value is used to convert the volume flow to a mass
flow.

User input:

5-digit floating-point number

Factory setting:

1 [unit]

Note!

The appropriate unit is taken from the function UNIT DENSITY (0420), (see Page 13).

⋅

Содержание Proline Promag 55



































































































































Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 55, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды