Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 130

background image

6 Discrete Output Function block

Device functions Proline Promag 55 FOUNDATION Fieldbus

120

Hauser

In the AUTO operating mode (automatic operation), the set point value (parameter SP_D) is
prescribed directly in the Discrete Output function block. In this case, the parameter CAS_IN_D is
not taken into consideration in the internal calculation.

In the MAN (manual) operating mode, the output value (parameter OUT_D) can be prescribed
directly in the Discrete Output function block. No internal calculation takes place.

6.2

Important functions and parameters
of the Discrete Output function block

The primary functions and parameters of the Discrete Output function block are listed below.

!

Note!
All FOUNDATION Fieldbus parameters available are described in the "FOUNDATION Fieldbus
Overview" Operating Instructions (BA013S) (available at:

→

www.endress.com

→

Download).

6.2.1

Selecting the operating mode

The operation mode is set by means of the MODE_BLK parameter group. The Discrete Output
function block supports the following operation modes:
• AUTO
• MAN
• CAS
• RCAS
• OOS

6.2.2

Safety behavior

There is a safety default available (fault state) for the Discrete Output function block. This is
activated when a fault condition (of the corresponding valid set point value) exists longer than
defined in the parameter FSTATE_TIME, or when the parameter SET_FSTATE in the Resource
Block is activated. The safety operation is determined via the parameters FSTATE_TIME,
FSTATE_VAL_D, and IO_OPTS.

6.2.3

Assignment between the Discrete Output Function block
and the Transducer Block

The assignment or connection between the Discrete Output function block and the Transducer
Block takes place in the Discrete Output function block via the parameter CHANNEL.

→

Parameter CHANNEL

→

16 (= Discrete Output function block)

«
...
118
119
120
121
122
...
»

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

Бренд: Bartington Страницы: 11

Бренд: Padwico Страницы: 28

Бренд: X-lite Страницы: 6

Бренд: Xerox Страницы: 13

Бренд: Xerox Страницы: 41

Бренд: XP-PEN Страницы: 3

E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...

Бренд: Olympus Страницы: 2

AS4000 - AS Transcription Kit

Бренд: Olympus Страницы: 24

Бренд: Insignia Страницы: 2

Бренд: PolyScience Страницы: 14

Бренд: Thermador Страницы: 20

OADM 21I6480/S14F

Бренд: Baumer Страницы: 4

Бренд: Home Accents Holiday Страницы: 2

Бренд: Metra Electronics Страницы: 4

REARSIGHT OnStar 250-8822

Бренд: Rostra Страницы: 2

Бренд: Godox Страницы: 31

Бренд: Swisher Страницы: 1

Бренд: Raytel LLC Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды