Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 130

background image

5 Analog Input function block

Device functions Proline Promag 55 FOUNDATION Fieldbus

114

Hauser

5.2

Important functions and parameters
of the Analog Input function blocks

The primary functions and parameters of the Analog Input function blocks are listed below.

!

Note!
All FOUNDATION Fieldbus parameters available are described in the "FOUNDATION Fieldbus
Overview" Operating Instructions (BA013S) (available at:

→

www.endress.com

→

Download).

5.2.1

Selecting the operating mode

The operation mode is set by means of the MODE_BLK parameter group. The Analog Input function
block supports the following operation modes:
• AUTO (automatic mode)
• MAN (manual mode)
• OOS (out of service)

!

Note!
The block status OOS is also shown via the parameter BLOCK_ERR. In operating mode OOS, if
write protection is not enabled, you can access all the write parameters without restriction.

5.2.2

Assignment of the process variable

The Promag 55 FOUNDATION Fieldbus has five Analog Input function blocks. The process
variables of the Transducer Block that are to be processed are assigned via the parameter
CHANNEL. The Promag 55 FOUNDATION Fieldbus is configured in the factory as follows:

• CHANNEL = 1

→

Calculated mass flow

• CHANNEL = 2

→

Volume flow

• CHANNEL = 7

→

Totalizer 1

• CHANNEL = 8

→

Totalizer 2

• CHANNEL = 9

→

Totalizer 3

5.2.3

Linearization types

In the Analog Input function block the input value can be linearized by the Transducer Block using
the parameter L_TYPE. The following types of linearization are available:

• Direct

With this setting the measured value from the Transducer Block (input value) avoids the
linearization function and is looped unchanged with the same unit through the Analog Input
function block.

• Indirect

With this setting the measured value from the Transducer Block (input value) is re-scaled linearly
via the input scaling XD_SCALE to the desired output range OUT_SCALE.

• Indirect Square Root

With this setting the measured value from the Transducer Block (input value) is re-scaled via the
parameter group XD_SCALE and recalculated using an evolution function. It is then rescaled
again to the desired output range via the parameter group OUT_SCALE.

«
...
112
113
114
115
116
...
»

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

Бренд: Zell Страницы: 33

Бренд: PASCO Страницы: 5

Бренд: PASCO Страницы: 4

Бренд: PASCO Страницы: 8

Бренд: PASCO Страницы: 4

Бренд: PASCO Страницы: 12

Бренд: PASCO Страницы: 5

Бренд: PASCO Страницы: 3

Бренд: PASCO Страницы: 8

Бренд: UniFlow Страницы: 42

Бренд: NavLinkz Страницы: 4

Бренд: Carefree Страницы: 12

TABFZ-G1-HS1117

Бренд: Tablet EX Gear Страницы: 2

RevitaSpa RS-L305A

Бренд: Air innovations Страницы: 12

Бренд: Lexicon Страницы: 14

Бренд: V-TAC Страницы: 136

Бренд: Doug Thorley Headers Страницы: 5

Бренд: Hama Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды