Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 110

Страница: 110 / 130

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

110

Hauser

Tot. 1 to 3 - Mode

AUTO - OOS

Use this parameter to define how the flow components are to be totaled by
the totalizer.

Options:

BALANCE
Positive and negative flow components. The positive and negative flow
components are balanced. In other words, net flow in the flow direction is
registered.

FORWARD
Positive flow components only

REVERSE
Negative flow components only

Factory setting:

Totalizer 1 = BALANCE
Totalizer 2 = FORWARD
Totalizer 3 = REVERSE

Tot. 1 to 3 - Reset

AUTO - OOS

Resets the totalizer "Tot. 1 to 3 - Sum" parameter to zero.

Options:

NO
YES

Factory setting:

Note!

Totalizer resetting can also be controlled or triggered by means of cyclic
data transfer via the Discrete Output function block.

Tot. - Reset All

AUTO - OOS

Resets all totalizers "Tot. 1 to 3 - Sum" parameter simultaneously to zero.

Options:

NO
YES

Factory setting:

Note!

Totalizer resetting can also be controlled or triggered by means of cyclic
data transfer via the Discrete Output function block.

Tot. - Failsafe All

AUTO - OOS

Use this parameter to define the common response of all Totalizers (1 to 3)
in case of error.

Options

STOP

→

The totalizers are paused until the fault is rectified.

ACTUAL VALUE

→

The totalizers continue to count based on the actual

flow measured value. The fault is ignored .

HOLD VALUE

→

The totalizers continue to count the flow based on the

last valid flow value (before the fault occurred).

Factory setting:

STOP

"Totalizer" Transducer Block/base index 1900:

Parameter

Write access with

operating mode

(MODE_BLK)

Description

Содержание Proline Promag 55



































































































































Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 55, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды