Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 130

background image

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

105

Info Line -
Display Mode

AUTO - OOS

!

Note!

The option is not active unless one of the following was selected in the
parameter "Info Line - Assign" (

• MASS FLOW BARGRAPH IN %
• VOLUME FLOW BARGRAPH IN %

Use this parameter to define the format of the bar graph.

Options:

STANDARD (Simple bar graph with 25 / 50 / 75% gradations and
integrated sign).

A0001258

SYMMETRY (Symmetrical bar graph for positive and negative directions of
flow, with –50 / 0 / +50% gradations and integrated sign).

A0001259

Factory setting:

STANDARD

Info Line Mux -
Assign

AUTO - OOS

Use this parameter to define the second reading to be displayed in the info
line alternately (every 10 seconds) with the value defined in the parameter
"Info Line - Assign" (

Options:

OFF
VOLUME FLOW IN %
MASS FLOW IN %
VOLUME FLOW BARGRAPH IN %
MASS FLOW BARGRAPH IN %
FLOW VELOCITY
OPERATING/SYSTEM CONDITIONS
DISPLAY FLOW DIRECTION
TOTALIZER (1 to 3)
AI1 - OUT VALUE
AI2 - OUT VALUE
AI3 - OUT VALUE
AI4 - OUT VALUE
AI5 - OUT VALUE
PID - IN VALUE (controlled variable)
PID - CAS IN VALUE (external set point)
PID - OUT VALUE (manipulated variable)
DEVICE PD-TAG (tag name)

Factory setting:

OFF

!

Note!

Multiplex mode is suspended as soon as a fault / notice message is
generated. The message in question appears on the display. Once the fault
is eliminated, the measuring device resumes operation in Multiplex mode
and the error message is no longer displayed on the local display.

"Display" Transducer Block/base index 1800:

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
103
104
105
106
107
...
»

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

Бренд: GE Страницы: 20

Бренд: GE Страницы: 2

Бренд: Acdeos Страницы: 7

CSL Elite Racing Wheel

Бренд: FANATEC Страницы: 2

Бренд: FANATEC Страницы: 8

Бренд: FANATEC Страницы: 35

Бренд: T-up Страницы: 14

Бренд: Tao Motor Страницы: 3

Бренд: Panasonic Страницы: 4

Бренд: Daikin Страницы: 52

McPherson Strut MIR 1G00

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 8

Бренд: Öhlins Страницы: 2

Бренд: SECURENET Страницы: 12

Бренд: Razorri Страницы: 26

Бренд: aquatherm Страницы: 32

Бренд: Metz Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды