Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 209

Страница: 209 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

209

Additional information

Description

The desired simulation value is defined in the

Switch status 1 to n

parameter.

Selection

• Off

Relay simulation is switched off. The device is in normal measuring mode or another

process variable is being simulated.

• On

Relay simulation is active.

Switch status 1 to n



Navigation

 Expert → Diagnostics → Simulation → Switch status 1 to n (0803–1 to n)

Prerequisite

The

option is selected in the

Switch sim. 1 to n

parameter parameter.

Description

Use this function to select a relay value for the simulation. In this way, users can verify the

correct adjustment of the relay output and the correct function of downstream switching

units.

Selection

• Open

• Closed

Additional information

Selection

• Open

Relay simulation is switched off. The device is in normal measuring mode or another

process variable is being simulated.

• Closed

Relay simulation is active.

Puls.outp.sim.



Navigation

 Expert → Diagnostics → Simulation → Puls.outp.sim. (0988)

Description

Use this function to switch simulation of the double pulse output on and off. The display

alternates between the measured value and a diagnostic message of the "Function check"

category (C) while simulation is in progress.

Selection

• Off

• Fixed value

• Down-count. val.

Factory setting

Off

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды