Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 161

Страница: 161 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

161

Factory setting

Enable

WLAN mode



Navigation

 Expert → Communication → WLAN settings → WLAN mode (2717)

Description

Use this function to select the WLAN mode.

Selection

• Access point

• WLAN Client

Factory setting

Access point

SSID name



Navigation

 Expert → Communication → WLAN settings → SSID name (2714)

Prerequisite

The client is activated.

Description

Use this function to enter the user-defined SSID name (max. 32 characters).

User entry

–

Factory setting

–

Network security



Navigation

 Expert → Communication → WLAN settings → Network security (2705)

Description

Use this function to select the type of security for the WLAN interface.

Selection

• Unsecured

• WPA2-PSK

• EAP-PEAP MSCHAP2

• EAP-PEAP NoAuth.

• EAP-TLS

Factory setting

Unsecured

Additional information

Selection

• Unsecured

Access the WLAN connection without identification.

• WPA2-PSK

Access the WLAN connection with a network key.

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды