Endress+Hauser Proline Promag 10 Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 124

background image

11 Description of Device Functions

PROline Promag 10

114

Hauser

11.13 Group SIMULATION SYSTEM

Function description SIMULATION SYSTEM

SIMULATION FAILSAFE
MODE

Use this function to set all outputs and the totalizer to their defined failsafe
modes, in order to check whether they respond correctly. During this time, the
words "SIMULATION FAILSAFE MODE" appear on the display.

Options:

ON
OFF

Factory setting:

OFF

SIMULATION
MEASURAND

Use this function to set all outputs and the totalizer to their defined flow-
response modes, in order to check whether they respond correctly. During this
time, the words “SIMULATION MEASURAND” appear on the display.

Options:

OFF
VOLUME FLOW

Factory setting:

OFF

"

Caution!

• The measuring device cannot be used for measuring while this simulation is

in progress.

• The setting is not saved if the power supply fails.

VALUE SIMULATION
MEASURAND

!

Note!

This function is not available unless the SIMULATION MEASURAND function is
active (= VOLUME FLOW).

Use this function to specify a selectable value (e.g. 12 m

3

/s).

This value is used to test downstream devices and the flowmeter itself.

User input:

5-digit floating-point number, [unit]

Factory setting:

0 [unit]

"

Caution!

The setting is not saved if the power supply fails.

!

Note!

The appropriate unit is taken from the SYSTEM UNITS group (see Page 93)

«
...
112
113
114
115
116
...
»

Содержание Proline Promag 10





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 10

Mentor Visual iQ

Бренд: GE Страницы: 2

Бренд: 2B Technologies Страницы: 4

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

Бренд: Hammond Organ Страницы: 25

Бренд: Hammond Organ Страницы: 87

Бренд: Unipulse Страницы: 129

Бренд: IDEAL Страницы: 11

Бренд: IDEAL Страницы: 16

PowerCross-Laser 8 S

Бренд: LaserLiner Страницы: 64

ClimaHome-Check Plus

Бренд: LaserLiner Страницы: 10

MeterMaster Plus

Бренд: LaserLiner Страницы: 104

Бренд: LaserLiner Страницы: 52

LaserRange-Master T2

Бренд: LaserLiner Страницы: 52

Бренд: LaserLiner Страницы: 5

CombiRangeXtender 40

Бренд: LaserLiner Страницы: 84

SuperCross-Laser 2P

Бренд: LaserLine Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды