Endress+Hauser Proline Fieldcheck Скачать руководство пользователя страница 74

Страница: 74 / 104

Device functions - thermal measuring systems

Proline Fieldcheck

Hauser

12.1.1

Group SIMULATION

Function group CONFIGURATION

Function description

FUNCTION



SIMULATION



CONFIGURATION

OPERATION MODE

Use this function to select the operation mode for the simulation.
Users can freely configure a flow signal from 0.0 to the displayed maximum value.

Display:

CONTINUOUS

The flow behavior in the process has low dynamics.

a0001708

Q1 = Simulation value 1

FLOW SPECIFICATION

Use this function to select which measurement is to be simulated.

Options:

MASS FLOW
CORRECTED VOLUME FLOW

Factory setting:

MASS FLOW

SIGNAL 1 LEVEL

Use this function to enter the flow value which is to be simulated.

Note!

More information is provided in the OPERATION MODE function.

User input:

0.000 to 999999 (6-digit positive floating-point number)

Note!

The flow velocity must lie within the value range from 0.0 m/s to the displayed
maximum value.

Unit:

The unit configured in the measuring device is adopted.

Factory setting:

0.000

START

STOP

Содержание Proline Fieldcheck









































































































Результаты поиска

Содержание Proline Fieldcheck

Отзывы:

Похожие инструкции для Proline Fieldcheck

Бренды по названию

Популярные бренды

Endress+Hauser Proline Fieldcheck, Руководство по эксплуатации

Результаты поиска

Содержание Proline Fieldcheck

Отзывы:

Похожие инструкции для Proline Fieldcheck

Бренды по названию

Популярные бренды