Endress+Hauser Proline Fieldcheck Скачать руководство пользователя страница 38

Страница: 38 / 104

Accessories

Proline Fieldcheck

Hauser

7.3

Service-specific accessories

7.4

Software history

Accessory

Description

Order code

FieldCare

FieldCare is Hauser's FDT-based plant asset
management tool.



It offers a wide variety of functionalities, from basic
device configuration to solutions for monitoring status.
FieldCare enables you to configure, operate and monitor
your plant.

Refer to product
page on the



Hauser
Web site



www.endress.com

Date

Software version

Changes to software

Operating Instructions

12.2011

1.07.XX

–

71158188/13.11

05.2010

1.07.XX

Introduction of Prosonic Flow 92F
Introduction of t-mass 65

71115488/03.10

04.2009

1.06.00

Introduction of sensor test box
Introduction of new languages

71068717/03.08

1.05.00

New internal basic software for Fieldcheck

–

02.2007

1.04.00

Introduction of Prosonic Flow 91
Introduction of Promag 55

50100084/12.04

07.2006

1.03.03

Bug fix

50100084/12.04

03.2005

1.03.01

Introduction of Prowirl 73
Introduction of Prosonic Flow 90
Introduction of Prosonic flow 93

50100084/12.04

08.2004

1.02.01

Bug fix

50100084/12.04

04.2004

1.02.00

Software extension for Prowirl 72

50100084/04.04

07.2003

1.01.00

Software extension for Coriolis flow measuring
systems

50100084/07.03

08.2002

1.00.02

Software adaptation

11.2001

1.00.01

Device release

50100084/08.01

–

1.00.00

–

Содержание Proline Fieldcheck









































































































Результаты поиска

Содержание Proline Fieldcheck

Отзывы:

Похожие инструкции для Proline Fieldcheck

Бренды по названию

Популярные бренды

Endress+Hauser Proline Fieldcheck, Руководство по эксплуатации

Результаты поиска

Содержание Proline Fieldcheck

Отзывы:

Похожие инструкции для Proline Fieldcheck

Бренды по названию

Популярные бренды