Endress+Hauser Proline Fieldcheck Скачать руководство пользователя страница 18

Страница: 18 / 104

Wiring

Proline Fieldcheck

Hauser

3.5.1

Connecting sensor test box to Promass 40, 80, 83, 84 field
housing

Note!
The start-up procedure must have been executed via the Simubox before connecting the sensor test
box.

Caution!
Connect the ground terminal of the adapter to the uninsulated housing components or to the
ground terminals in the connection compartment.

Connect the sensor test box to Fieldcheck with the simulation cable.

Connect the sensor test box to the sensor cable connector and the excitation coil connector
with the Coriolis adapter.

A0013401

Fig. 11:

Coriolis adapter for sensor test box

Sensor test box

Coriolis adapter

Excitation current connector Promass 40

Excitation current connector Promass 80, 83, 84

Signal coil connector Promass 40

Signal coil connector Promass 80, 83, 84

Ground terminal

Connection to Fieldcheck (with Simubox cable)

Содержание Proline Fieldcheck









































































































Результаты поиска

Содержание Proline Fieldcheck

Отзывы:

Похожие инструкции для Proline Fieldcheck

Бренды по названию

Популярные бренды

Endress+Hauser Proline Fieldcheck, Руководство по эксплуатации

Результаты поиска

Содержание Proline Fieldcheck

Отзывы:

Похожие инструкции для Proline Fieldcheck

Бренды по названию

Популярные бренды