Endress+Hauser PROFIBUS-DP, Руководство по эксплуатации, Страница: 46 / 52

SmarTec S CLD 132 PROFIBUS-PA/-DP Troubleshooting
46 EHauser
9 Troubleshooting
9.1 System error messages
DIAGNOSIS and DIAGNOSIS_EXTENSION parameters
The DIAGNOSIS and DIAGNOSIS_EXTENSION parameters are generated from the
device-specific errors.
SmarTec S CLD 132 PROFIBUS diagnosis
NAMUR
class Error
no. Description DIAGNOSIS DIAGNOSIS_
EXTENSION Measured value status
Quality Sub-status
Failure E001 Memory error 01 00 00 80 - DIA_HW_ELECTR 01 00 00 00 00 00 BAD Device failure 0C
Failure E002 Data error in EEPROM 10 00 00 80 - DIA_MEM_CHKSUM 02 00 00 00 00 00 BAD Device failure 0C
Failure E003 Invalid configuration 00 04 00 80 - DIA_CONF_INVAL 04 00 00 00 00 00 BAD Device failure 0C
Failure E007 Transmitter faulty 20 00 00 80 - DIA_MEASUREMENT 08 00 00 00 00 00 BAD Device failure 0C
Failure E008 Sensor or sensor
connection faulty 20 00 00 80 - DIA_MEASUREMENT 10 00 00 00 00 00 BAD Sensor failure 10
Failure E010 Temperature sensor
defective 20 00 00 80 - DIA_MEASUREMENT 20 00 00 00 00 00 BAD Sensor failure 10
Failure E025 Limit value for Airset-
Offset exceeded 20 00 00 80 - DIA_MEASUREMENT 40 00 00 00 00 00 BAD Configuration
error 04
Failure E036 Sensor calibration range
exceeded 20 00 00 80 - DIA_MEASUREMENT 80 00 00 00 00 00 BAD Configuration
error 04
Failure E037 Sensor calibration range
undershot 20 00 00 80 - DIA_MEASUREMENT 00 01 00 00 00 00 BAD Configuration
error 04
Failure E045 Calibration aborted 20 00 00 80 - DIA_MEASUREMENT 00 02 00 00 00 00 BAD Configuration
error 04
Failure E049 Installation factor
exceeded 20 00 00 80 - DIA_MEASUREMENT 00 04 00 00 00 00 BAD Configuration
error 04
Failure E050 Installation factor
undershot 00 20 00 80 - DIA_MAINTENANCE 00 08 00 00 00 00 BAD Configuration
error 5C
Failure E055 Measuring range of the
main parameter
undershot 20 00 00 80 - DIA_MEASUREMENT 00 10 00 00 00 00 UNCERTAIN Sensor
conversion not
accurate
50
Failure E057 Measuring range of the
main parameter
exceeded 20 00 00 80 - DIA_MEASUREMENT 00 20 00 00 00 00 UNCERTAIN Sensor
conversion not
accurate
50
Failure E059 Temperature range
undershot 20 00 00 80 - DIA_MEASUREMENT 00 40 00 00 00 00 UNCERTAIN Sensor
conversion not
accurate
50
Failure E061 Temperature range
exceeded 20 00 00 80 - DIA_MEASUREMENT 00 80 00 00 00 00 UNCERTAIN Sensor
conversion not
accurate
50
Failure E067 Limit contactor set point
exceeded 00 20 00 80 - DIA_MAINTENANCE 00 00 00 04 00 00 UNCERTAIN Non-specific 40
Failure E077 Temperature outside of
the
α
value table
00 04 00 80 - DIA_CONF_INVAL 00 00 01 00 00 00 BAD Configuration
error 04
Failure E078 Temperature outside of
the concentration table 00 04 00 80 - DIA_CONF_INVAL 00 00 02 00 00 00 BAD Configuration
error 04
Failure E079 Conductivity outside of
the concentration table 0 04 00 80 - DIA_CONF_INVAL 00 00 04 00 00 00 BAD Configuration
error 04