Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 182

background image

Commissioning

Proline Promag 53 PROFIBUS DP/PA

104

Hauser

6.4.2

PROFIBUS PA commissioning

The following steps must be carried out in the sequence specified:

1.

Check the hardware write protection:

The WRITE PROTECT (6102) parameter indicates whether it is possible to write to the device
parameters via PROFIBUS (acyclic data transmission, e.g. via FieldCare).

!

Note!

• This check is not needed if operating via the local display.

BASIC FUNCTION (G)

→

PROFIBUS PA (GCA)

→

CONFIGURATION (610)

→

WRITE PROTECT (6102)

→

Display of one of the following options:

– OFF (factory setting) = write access via PROFIBUS possible
– ON = write access via PROFIBUS not possible

Deactivate the write protection if necessary.

2.

Enter the tag name (optional):

BASIC FUNCTION (G)

→

PROFIBUS PA (GCA)

→

CONFIGURATION (610)

→

TAG NAME (6100)

3.

Configuring the fieldbus address:

• Software addressing using the local display:

BASIC FUNCTION (G)

→

PROFIBUS PA (GCA)

→

CONFIGURATION (610)

→

FIELDBUS ADDRESS (6101)

• Hardware addressing via miniature switches

4.

Select the system unit:

a. Determine the units by means of the system units group:

MEASURED VARIABLES (A)

→

SYSTEM UNITS (ACA)

→

CONFIGURATION (040)

→

UNIT MASS FLOW (0400) / UNIT MASS (0401) / UNIT
VOLUME FLOW (0402) / ...

b. In the function UNIT TO BUS (6141), select the option SET UNITS, so that the measured

variables transmitted cyclically to the PROFIBUS master (Class 1) are transmitted with the
system units set in the measuring device:
BASIC FUNCTION (G)

→

PROFIBUS PA (GCA)

→

OPERATION (614)

→

UNIT TO BUS (6141)

!

Note!

– The configuration of the system units for the totalizer is described separately

→

see step 6

– If the system unit of a measured variable is changed by means of the local operation or an

operating program, this initially does not have any effect on the unit that is used to transmit
the measured variable to the PROFIBUS master (Class 1). Changed system units of the
measured variables are not transmitted to the PROFIBUS master (Class 1) until the SET
UNITS option is activated in the function BASIC FUNCTION (G)

→

PROFIBUS PA (GCA)

→

OPERATION (614)

→

UNIT TO BUS (6141).

5.

Setting the measuring mode:

In the function MEASURING MODE (6601), select the flow portions to be measured by the
measuring device.

BASIC FUNCTION (G)

→

SYSTEM PARAMETER (GLA)

→

CONFIGURATION (660)

→

MEASURING MODE (6601)

→

Selection of one of the following options:

– UNIDIRECTIONAL (factory setting) = only the positive flow portions
– BIDIRECTIONAL = the positive and negative flow components

«
...
102
103
104
105
106
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: Panasonic Страницы: 180

Бренд: WAGER Страницы: 36

Бренд: K-Patents Страницы: 10

Бренд: National Instruments Страницы: 15

Portable Grand DGX-670

Бренд: Yamaha Страницы: 93

Portatone PSR-410

Бренд: Yamaha Страницы: 65

Бренд: Topcon Страницы: 62

AccuPoint 2 ATP

Бренд: Neogen Corporation Страницы: 16

Бренд: az-instrument Страницы: 12

Concert Monochord

Бренд: FEELTONE Страницы: 8

Бренд: Duratool Страницы: 4

Бренд: International Light Technologies Страницы: 19

Бренд: Bante Instruments Страницы: 7

Бренд: dallmeier Страницы: 93

Бренд: TE Connectivity Страницы: 5

Бренд: B&K Страницы: 64

Бренд: Rodgers Страницы: 54

Бренд: Behringer Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды