Endress+Hauser MODBUS RS485 Скачать руководство пользователя страница 77

Страница: 77 / 92

LPGmass Modbus RS485

Technical data

Hauser

Current consumption

Transmitter

Order code for "Output"

Maximum

Current consumption

Maximum

switch-on current

Option

: Modbus RS485, for use in intrinsically safe

areas

145 mA

16 A (< 0.4 ms)

Safety Barrier Promass 100

Order code for "Output"

Maximum

Current consumption

Maximum

switch-on current

Option

: Modbus RS485, for use in intrinsically safe

areas

230 mA

10 A (< 0.8 ms)

Power supply failure

• Totalizers stop at the last value measured.

• Configuration is retained in the device memory.

• Error messages (incl. total operated hours) are stored.

Electrical connection

→  25

Potential equalization

→  27

Terminals

Transmitter

Spring terminals for wire cross-sections0.5 to 2.5 mm

(20 to 14 AWG)

Safety Barrier Promass 100

Plug-in screw terminals for wire cross-sections0.5 to 2.5 mm

(20 to 14 AWG)

Cable entries

• Cable gland: M20 × 1.5 with cable 6 to 12 mm (0.24 to 0.47 in)

• Thread for cable entry:

– NPT ½"

– G ½"

– M20

Cable specification

→  22

16.6 Performance characteristics

reference operating

conditions

• Error limits based on ISO 11631

• Water with +15 to +45 °C (+59 to +113 °F) at2 to 6 bar (29 to 87 psi)

• Specifications as per calibration protocol

• Accuracy based on accredited calibration rigs that are traced to ISO 17025.

To obtain measured errors, use the

Applicator

sizing tool →  73

Maximum measured error

Base accuracy

Design fundamentals →  79

Содержание MODBUS RS485





























































































Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды

Endress+Hauser MODBUS RS485, Руководство по эксплуатации

Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды