Endress+Hauser MODBUS RS485 Скачать руководство пользователя страница 36

Страница: 36 / 92

System integration

LPGmass Modbus RS485

Hauser

System integration

9.1

Overview of device description files

9.1.1

Current version data for the device

Firmware version

01.03.zz

• On the title page of the Operating instructions
• On the transmitter nameplate
• Firmware version

Diagnostics → Device information → Firmware
version

Release date of firmware version

10.2014

---

For an overview of the different firmware versions for the device

9.1.2

Operating tools

The suitable device description file for the individual operating tools is listed in the table

below, along with information on where the file can be acquired.

FieldCare

•

www.endress.com

→ Download Area

• CD–ROM (contact Hauser)
• DVD (contact Hauser)

DeviceCare

•

www.endress.com

→ Download Area

• CD–ROM (contact Hauser)
• DVD (contact Hauser)

9.2

Modbus RS485 information

9.2.1

Function codes

Function codes are used to define which read or write action is carried out via the Modbus

protocol. The measuring device supports the following function codes:

Code

Name

Description

Application

Read holding
register

Master reads one or more Modbus
registers from the device.
A maximum of 125 consecutive
registers can be read with 1
telegram: 1 register = 2 bytes



The measuring device does
not make a distinction
between function codes 03
and 04; these codes therefore
yield the same result.

Read device parameters with read
and write access
Example:
Read mass flow

Read input
register

Master reads one or more Modbus
registers from the device.
A maximum of 125 consecutive
registers can be read with 1
telegram: 1 register = 2 bytes



The measuring device does
not make a distinction
between function codes 03
and 04; these codes therefore
yield the same result.

Read device parameters with read
access
Example:
Read totalizer value

Содержание MODBUS RS485





























































































Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды

Endress+Hauser MODBUS RS485, Руководство по эксплуатации

Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды