Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 85

Страница: 85 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Commissioning (block-based operation)

Hauser

Step

Block

Parameter

Action

SETUP (TRDSUP)

Empty calibration
(empty_calibration)

Enter the distance E between the
reference point R and the minimum level
(0%).

SETUP (TRDSUP)

Full calibration (full_calibration) Enter distance F between the minimum

(0%) and maximum (100%) level.

SETUP (TRDSUP)

Level (level)

Displays the measured level L.

SETUP (TRDSUP)

Distance (filtered_dist_val)

Displays the distance D between the
reference point R and the level L.

SETUP (TRDSUP)

Signal quality (signal_quality)

Displays the signal quality of the level
echo.

SETUP (TRDSUP)

Confirm distance
(confirm_distance)

Compare the displayed distance to the real
distance in order to start the recording of
the mapping curve.

Selection:

• 179: Manual map
• 32847: Factory map
• 32859: Distance ok
• 32860: Distance too big
• 32861: Distance too small
• 32862: Distance unknown
• 33100: Tank empty

12.6 Configuration of the on-site display

12.6.1 Factory settings of the on-site display for level measurements

Parameter

Factory setting

Format display

1 value, max. size

Value 1 display

Level linearized

Value 2 display

None

Value 3 display

None

Value 4 display

None

The on-site display can be adjusted in the

DISPLAY (TRDDISP)

transducer block.

12.7 Configuration management

After commissioning, you can save the current device configuration, copy it to another

measuring point or restore the previous device configuration. You can do so using the

Configuration management

parameter and its options.

Navigation path in the operating menu

Setup → Advanced setup → Conf.backup disp → Config. managem.

Block operation

Block:

DISPLAY (TRDDISP)

Parameter:

Configuration management (configuration_management)

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды