Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 127

Страница: 127 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Operating menu

Hauser

127

17.3 "Setup" menu

•

: Marks the navigation path to the parameter via the display and operating

module.

•

: Marks the navigation path to the parameter via an operating tool (e.g.

FieldCare).

•

: Marks parameters which can be locked via the software locking →  48.

Navigation

 Setup

Distance unit



Navigation

 Setup → Distance unit

Description

Select distance unit.

Selection

SI units

• mm

• m

US units

• ft

• in

Factory setting

Bin type



Navigation

 Setup → Bin type

Prerequisite

Medium type (→  139)

Solid

Description

Specify bin type.

Selection

• Buffer silo (fast)

• Bin / Pile

• Crusher / belt

• Silo

• Workbench test

Factory setting

Silo

Max. filling speed solid



Navigation



Setup → Max. fill. solid

Prerequisite

Medium type (→  139)

Solid

Description

Select expected maximum filling speed.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды