Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 12

Страница: 12 / 198

Basic safety instructions

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Hauser

Basic safety instructions

2.1

Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill

the following requirements:

‣

Trained, qualified specialists must have a relevant qualification for this specific function

and task.

‣

Are authorized by the plant owner/operator.

‣

Are familiar with federal/national regulations.

‣

Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the

application).

‣

Follow instructions and comply with basic conditions.

The operating personnel must fulfill the following requirements:

‣

Are instructed and authorized according to the requirements of the task by the facility's

owner-operator.

‣

Follow the instructions in this manual.

2.2

Designated use

Application and measured materials

The measuring device described in these Operating Instructions is intended for the

continuous, contactless level measurement of mainly bulk solids. The device can also be

freely mounted outside closed metal vessels (e.g. above basins, open channels or open

piles) because of its operating frequency of about 26 GHz, a maximum radiated pulsed

power of 23.3 mW and an average power output of 0.076 mW. Operation is completely

harmless to humans and animals.
Observing the limit values specified in the "Technical data" and listed in the Operating

Instructions and supplementary documentation, the measuring device may be used for the

following measurements only:

‣

Measured process variables: level, distance, signal strength

‣

Calculated process variables: Volume or mass in arbitrarily shaped vessels; flow

through measuring weirs or flumes (calculated from the level by the linearization

functionality)

To ensure that the measuring device remains in proper condition for the operation time:

‣

Use the measuring device only for measured materials against which the process-

wetted materials are adequately resistant.

‣

Observe the limit values in "Technical data".

Incorrect use

The manufacturer is not liable for damage caused by improper or non-designated use.
Verification for borderline cases:

‣

For special measured materials and cleaning agents, Hauser is glad to provide

assistance in verifying the corrosion resistance of wetted materials, but does not accept

any warranty or liability.

Residual risk

The electronics housing and its built-in components such as display module, main

electronics module and I/O electronics module may heat to 80 °C (176 °F) during operation

through heat transfer from the process as well as power dissipation within the electronics.

During operation the sensor may assume a temperature near the temperature of the

measured material.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды