Endress+Hauser LT5 Скачать руководство пользователя страница 21

Страница: 21 / 96

LT5

Installation

Hauser

5.2

Installation preparation

Be sure to perform the following operations prior to installing LT.
• The gauge head should be installed in a place where the meter can be read easily.

• The float must be installed so that it is positioned near the tank's side wall.

• In a spherical tank, the float must be installed so that it is positioned near the center of

the tank.

• If the roof of a dome-roof tank has a steep incline, the float must be installed so that it is

positioned near the center of the tank.

• Use an appropriate gasket on the flange connection to maintain airtightness.

CAUTION

Risk of tape severing

‣

The float should be positioned as far from the tank inlet or stirrer as possible so that

the waves do not directly impact the float. If there is no choice but to position the float

near the inlet or stirrer, install a wave guard to protect the float. Rapid injection of

liquid near the float may cause the tape to sever.

A0039946

 11

Installation conditions

Center of the float

Wave guard installation

Tank

Liquid inlet

Содержание LT5

































































































Результаты поиска

Содержание LT5

Отзывы:

Похожие инструкции для LT5

Бренды по названию

Популярные бренды

Endress+Hauser LT5, Руководство по эксплуатации

Результаты поиска

Содержание LT5

Отзывы:

Похожие инструкции для LT5

Бренды по названию

Популярные бренды