Endress+Hauser Liquiphant FTL64 Скачать руководство пользователя страница 52

Страница: 52 / 64

Accessories

Liquiphant FTL64

Hauser

27.5

(1.08)

(1.57)

A0022292

 47

Plug-in jack M12 IP67. Unit of measurement mm (in)

13.6 Bluetooth module VU121 (optional)

The Bluetooth module can be connected to the following electronic inserts via the COM

interface: FEL61, FEL62, FEL64, FEL64DC, FEL67, FEL68 (2-wire NAMUR).
• Bluetooth module without battery for use in conjunction with electronic inserts FEL61,

FEL62, FEL64, FEL64DC and FEL67

Order number: 71437383

• Bluetooth module with battery for use in conjunction with electronic insert FEL68 (2-

wire NAMUR)

Order number: 71437381

Contains

FCC ID:

IC:

A0039257

 48

Bluetooth module VU121

More detailed information and documentation are available:

• Product Configurator on the Hauser website

www.endress.com

• Hauser sales organization

www.addresses.endress.com

A tall cover is required (transparent plastic cover or aluminum cover with sight glass)

when using or retrofitting the Bluetooth module. The Bluetooth module cannot be

used in conjunction with the single compartment 316L housing, cast. The cover

depends on the housing and approval of the device.

13.7 LED module VU120 (optional)

A brightly lit LED indicates the operational status (switch status or alarm status). The LED

module can be connected to the following electronic inserts: FEL62, FEL64, FEL64DC.
Order number: 71437382

Содержание Liquiphant FTL64

































































Результаты поиска

Содержание Liquiphant FTL64

Отзывы:

Похожие инструкции для Liquiphant FTL64

Бренды по названию

Популярные бренды

Endress+Hauser Liquiphant FTL64, Руководство по эксплуатации

Результаты поиска

Содержание Liquiphant FTL64

Отзывы:

Похожие инструкции для Liquiphant FTL64

Бренды по названию

Популярные бренды