Endress+Hauser Liquiline To Go Ex CYM291 Скачать руководство пользователя страница 18

Страница: 18 / 64

Cond

Configuring

Configuration (Cond)

Configuration is required to match the connected sensor and the
desired measurement performance. Furthermore, you can select the
suitable calibration method. The following table gives you an over-
view. Factory settings are shown in bold print.

Measurement

“Setup” display

Select using arrow keys, confirm by pressing .

s
t

Display

Cond | SAL g/kg | TDS mg/l

MOHM cm

OFF | On

Cond Unit

mS/cm | S/m

TDS Factor

0.0 … 1.0 (if display = TDS)

TC *

OFF | LINEAR | NLF | NACL | HCL | NH3 | NAOH
(if display = Cond)

TC LINEAR

0.0 … 20.0 %/K | 2.1 %/K (if TC = LINEAR)

REF. Temp.

0 … 100 °C | 25 °C

(

32 … 212 °F | 77 °F)

(if TC = LINEAR)

CAL

Auto OFF

OFF | 0.1h | 1h | 6h | 12h

Temp. Unit

°C | °F

Time Format

24h | 12h

Date Format

dd.mm.yy | mm.dd.yy

Default

NO | YES (reset to factory settings)
Note: All data logger entries will be deleted.

This icon prompts you to select a menu item using the arrow keys –
the selection is confirmed by pressing .

* Temperature compensation

Содержание Liquiline To Go Ex CYM291

































































Результаты поиска

Содержание Liquiline To Go Ex CYM291

Отзывы:

Похожие инструкции для Liquiline To Go Ex CYM291

Бренды по названию

Популярные бренды

Endress+Hauser Liquiline To Go Ex CYM291, Руководство по эксплуатации

Результаты поиска

Содержание Liquiline To Go Ex CYM291

Отзывы:

Похожие инструкции для Liquiline To Go Ex CYM291

Бренды по названию

Популярные бренды