Endress+Hauser Liquiline To Go CYM290 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

background image

32

pH

Oxy Cond

Measuring

Once you have completed all preparations, you can start with the actual measure-
ment.

1) Connect the desired sensor to the meter. Some sensors require a special prepara-

tion. Please proceed according to the operating instructions for the sensor.

2) Switch the device on using the

or

key.

3) Depending on the measurement method and the sensor used, immerse the

sensing part of the sensor in the medium to be measured.

4) Watch the display and wait for the reading to stabilize.

Toggling the Measured Value Display

During measurement, you can toggle between display of primary / secondary
measured value and clock by pressing

.

Adjusting the Temperature

When you connect a sensor without temperature detector, you can manually adjust
the temperature for measurement or calibration:
1) Press

to access measuring mode. The adjusted temperature will be displayed.

2) Set the desired temperature value using the



or



arrow.

Holding the key depressed changes the temperature value at high speed.

«
...
30
31
32
33
34
...
»

Содержание Liquiline To Go CYM290

































































Отзывы:

Нет отзывов

Похожие инструкции для Liquiline To Go CYM290

Бренд: UEi Страницы: 4

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

NUFLO Scanner 2000 microEFM

Бренд: Cameron Страницы: 8

IEM-100 Beltpack

Бренд: DAPAudio Страницы: 19

Бренд: OHAUS Страницы: 52

Бренд: Magene Страницы: 80

Бренд: janitza Страницы: 128

Бренд: Jaquet Страницы: 27

Бренд: Bühler technologies Страницы: 33

Бренд: LaserLiner Страницы: 84

Бренд: S&T Страницы: 23

Бренд: UEi Страницы: 5

Бренд: Anglerfish Creative Lighting Страницы: 15

Бренд: Oceanic Страницы: 64

Бренд: RADWAG Страницы: 12

Бренд: Metrohm Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды