Endress+Hauser Liquiline To Go CYM290 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 64

background image

28

Cond

Calibration

Conductivity Calibration

1)  In measuring mode, press the Menu softkey.
2)  Select “Configuration” and confirm by pressing E.
3)  Select the desired “Calibration mode”.
4)  Perform the selected calibration as described on the following pages.

Follow the instructions on the display.

Auto Calibration

(Automatic calibration with specification of the calibration solution used)
5) Select the calibration solution:

5 °C

10°C

15 °C

20 °C

25 °C

30 °C

35 °C

40 °C

50 °C

CLY 11-A

46.4

52.9

59.7

66.7

74.0

81.4

88.8

96.5

112.2 µS/

cm

CLY 11-B

93.9

107.1

120.8

135.2

149.6

164.5

179.7

195.1

226.8

CLY 11-C

0.8

1.010

1.136

1.270

1.406

1.542

1.683

1.824

2.114

mS/

cm

CLY 11-D 8.07

9.16

10.29

11.45

12.64

13.86

15.11

16.37

18.97

CLY 11-E 70.58 79.34

88.20

97.56 107.00 116.52 126.10 135.98 155.82

6) Press the Start softkey.
7) Immerse the sensor in the solution and press Continue.

8) Finally, the calibration data record will be displayed.

You can Apply or Discard these values.

NOTICE!
• Make sure that the values of the calibration solutions used corre-

spond exactly to those specified in this manual. If not, the resulting
cell constant will be incorrect.

• When calibrating in a liquid, make sure that the sensor, the separate

temperature probe (if present) and the calibration solution have
the same temperature. Only this ensures that the cell constant is
determined correctly.

Note: To abort calibration, you can press

at any time.

«
...
26
27
28
29
30
...
»

Содержание Liquiline To Go CYM290

































































Отзывы:

Нет отзывов

Похожие инструкции для Liquiline To Go CYM290

Бренд: Oakton Страницы: 4

IEM-100 Beltpack

Бренд: DAPAudio Страницы: 19

Бренд: Parkside Страницы: 114

Бренд: WAGNER Страницы: 9

Бренд: G-Tek Страницы: 83

Бренд: Magene Страницы: 80

Бренд: Palstar Страницы: 15

Бренд: Ansul Страницы: 24

Бренд: ENDA Страницы: 2

Бренд: Heinrichs Страницы: 31

Vigilantplant NFBU200-S Series

Бренд: YOKOGAWA Страницы: 24

Бренд: horiba Страницы: 117

Бренд: Sequid Страницы: 111

Бренд: OHAUS Страницы: 71

Бренд: Analog Arts Страницы: 8

Heavy Duty 2270-20

Бренд: Milwaukee Страницы: 33

Бренд: kruss Страницы: 115

Бренд: Jaquet Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды