Endress+Hauser Liquiline To Go CYM290 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 64

background image

12

Start-Up

Inserting the Batteries

With four AA batteries, the CYM290 has an
operating time of up to 500 h when oper-
ated in logger mode (see page 36).
Open the battery compartment on the
rear of the device. Be sure to observe the
correct polarity when inserting the batter-
ies (see markings in the battery chamber).
Close the battery compartment cover and
screw it handtight.

Check the shipment for transport damage and completeness (see Package
Contents).

NOTICE!
Do not operate the device when one of the following conditions
applies:
•  the device shows visible damage
•  the device fails to perform the intended function
•  prolonged storage at temperatures above 70 °C
•  severe transport stresses
In this case, a professional routine test must be performed.
This test should be carried out at our factory.

A special lithium-ion battery suited to the battery compartment is available for the
Liquiline To Go CYM290. The battery is recharged through the USB port.

A battery icon in the display indicates the battery power level:

Icon fully filled

Batteries at full capacity

Icon partially filled

Battery capacity is sufficient

Icon empty

Battery capacity not sufficient;
calibration is possible, no logging

Icon blinks

Only a few operating hours remaining,
measurement is still possible.
NOTICE! It is absolutely necessary to replace the
batteries.

«
...
10
11
12
13
14
...
»

Содержание Liquiline To Go CYM290

































































Отзывы:

Нет отзывов

Похожие инструкции для Liquiline To Go CYM290

Бренд: janitza Страницы: 12

Бренд: janitza Страницы: 84

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 14

Бренд: janitza Страницы: 98

Бренд: Van Walt Страницы: 12

Бренд: QuadTech Страницы: 76

Бренд: Ulvac Страницы: 18

Бренд: YOKOGAWA Страницы: 14

Бренд: Kobold Страницы: 44

International 2S Pro

Бренд: Brantz Страницы: 2

Бренд: Salutron Страницы: 2

Бренд: Kipp & Zonen Страницы: 32

Бренд: OHAUS Страницы: 6

ACCURE 2350-GAS

Бренд: ROOTECH Страницы: 26

Бренд: THORLABS Страницы: 49

Бренд: Hanna Instruments Страницы: 15

Бренд: horiba Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды