Endress+Hauser iTHERM TrustSens TM371 Скачать руководство пользователя страница 9

Страница: 9 / 106

iTHERM TrustSens TM371, TM372

Incoming acceptance and product identification

Hauser

Parts in contact with the medium

Parts of the thermometer in contact with the medium comply with the following European

regulations:

• (EC) No. 1935/2004, Article 3, paragraph 1, Articles 5 and 17 on materials and articles

intended to come into contact with food.

• (EC) No. 2023/2006 on good manufacturing practice for materials and articles intended

to come into contact with food.

• (EU) No. 10/2011 on plastic materials and articles intended to come into contact with

food.

3.3

Transport and storage

Pack the device in such a way as to protect it reliably against impact for storage (and

transportation). The original packaging provides optimum protection.

Storage temperature

–40 to +85 °C (–40 to +185 °F)

Содержание iTHERM TrustSens TM371











































































































Результаты поиска

Содержание iTHERM TrustSens TM371

Отзывы:

Бренды по названию

Популярные бренды

Endress+Hauser iTHERM TrustSens TM371, Руководство по эксплуатации

Результаты поиска

Содержание iTHERM TrustSens TM371

Отзывы:

Бренды по названию

Популярные бренды