Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 9

Страница: 9 / 100

iTEMP TMT85

Incoming acceptance and product identification

Hauser

Incoming acceptance and product

identification

3.1

Incoming acceptance

1. Unpack the temperature transmitter carefully. Is the packaging or content free from

damage?
 Damaged components may not be installed as the manufacturer can otherwise

not guarantee compliance with the original safety requirements or the material

resistance, and can therefore not be held responsible for any resulting damage.

2. Is the delivery complete or is anything missing? Check the scope of delivery against

your order.

3. Does the nameplate match the ordering information on the delivery note?
4. Are the technical documentation and all other necessary documents provided? If

applicable: are the Safety Instructions (e.g. XA) for hazardous areas provided?

If one of these conditions is not satisfied, contact your Hauser Sales Center.

3.2

Product identification

The following options are available for identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

• Enter the serial number from the nameplate in the

W@M Device Viewer

(

www.endress.com/deviceviewer

): All data relating to the device and an overview of the

Technical Documentation supplied with the device are displayed.

• Enter the serial number on the nameplate into the

Hauser Operations App

scan the 2-D matrix code (QR code) on the nameplate with the

Hauser

Operations App

: all the information about the device and the technical documentation

pertaining to the device is displayed.

3.2.1

Nameplate

The right device?

Compare and check the data on the nameplate of the device against the requirements of

the measuring point:

11-42V

012345678910

xx.yy.zz

TMT82- XXXXX/XX

iTEMP

Made in Germany 201x
D-87484 Nesselwang

Ser.no.:

FW:

Input:

12345678ABCDEFGH
12345678ABCDEFGH

Dev.Rev: x

Ext. ord. cd.:
XXXXXXXXXXXXX#

A0014561

 1

Nameplate of the head transmitter (example, Ex version)

Power supply, current consumption and radio approval (Bluetooth)

Serial number, device revision, firmware version and hardware version

Data Matrix 2D code

2 lines for the TAG name and extended order code

Approval in hazardous area with number of the relevant Ex documentation (XA...)

Approvals with symbols

Order code and manufacturer ID

Содержание iTEMP TMT85





































































































Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды

Endress+Hauser iTEMP TMT85, Руководство по эксплуатации

Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды