Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 91

Страница: 91 / 202

Proline t-mass I 300 HART

Commissioning

Hauser

Parameter

Prerequisite

Description

Selection / User
interface / User

entry

Factory setting

0/4 mA value

One of the following options is
selected in the

Current span

parameter (→  90):
• 4...20 mA NAMUR

(3.8...20.5 mA)

• 4...20 mA US (3.9...20.8

mA)

• 4...20 mA (4... 20.5 mA)
• 0...20 mA (0... 20.5 mA)

Enter 4 mA value.

Signed floating-point
number

–

20 mA value

In the

Current span

parameter

(→  90), one of the
following options is selected:
• 4...20 mA NAMUR

(3.8...20.5 mA)

• 4...20 mA US (3.9...20.8

mA)

• 4...20 mA (4... 20.5 mA)
• 0...20 mA (0... 20.5 mA)

Enter 20 mA value.

Signed floating-point
number

Depends on country
and nominal
diameter

Fixed current

The

Fixed current

option is

selected in the

Current span

parameter (→  90).

Defines the fixed output
current.

0 to 22.5 mA

22.5 mA

Damping output 1 to n

A process variable is selected
in the

Assign current output

parameter (→  90) and one
of the following options is
selected in the

Current span

parameter (→  90):
• 4...20 mA NAMUR

(3.8...20.5 mA)

• 4...20 mA US (3.9...20.8

mA)

• 4...20 mA (4... 20.5 mA)
• 0...20 mA (0... 20.5 mA)

Set reaction time for output
signal to fluctuations in the
measured value.

0.0 to 999.9 s

–

Failure mode

A process variable is selected
in the

Assign current output

parameter (→  90) and one
of the following options is
selected in the

Current span

parameter (→  90):
• 4...20 mA NAMUR

(3.8...20.5 mA)

• 4...20 mA US (3.9...20.8

mA)

• 4...20 mA (4... 20.5 mA)
• 0...20 mA (0... 20.5 mA)

Define output behavior in
alarm condition.

• Min.
• Max.
• Last valid value
• Actual value
• Defined value

–

Failure current

The

Defined value

option is

selected in the

Failure mode

parameter.

Enter current output value in
alarm condition.

0 to 22.5 mA

22.5 mA

Visibility depends on order options or device settings

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды