Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 148

background image

Proline Promass 83

Technical data

Hauser

133

Secondary containment
pressure rating

The material load diagrams (pressure-temperature diagrams) for the process connections
are provided in the separate "Technical Information" document on the device in question.
This can be downloaded as a PDF file from www.endress.com. A list of the "Technical
Information" documents available is provided in the "Documentation" section

Pressure ranges of secondary containment:

Promass A:

25 bar (362) psi

Promass E:

No secondary containment pressure rating

Promass F:

DN 8 to 50 (3/8 to 2"): 40 bar (580 psi)
DN 80 (3"): 25 bar (362 psi)
DN 100 to 150 (4 to 6"): 16 bar (232 psi)
DN 250(10"): 10 bar (145 psi)

Promass H:

!

Note!
Only one pressure rating for Promass H, use values for Tantalum version:
• DN 8 to 25 (3/8 to 1"): 25 bar (362 psi)
• DN 40 to 50 (1½ to 2"): 16 bar (232 psi)

Promass I:

40 bar (580 psi)

Promass P:

DN 8 to 25 (3/8 to 1"): 25 bar (362 psi)
DN 40 (1½"): 16 bar (232 psi)
DN 50 (2"): 10 bar (145 psi)

Promass S:

DN 8 to 25 (3/8 to 1"): 25 bar (362 psi)
DN 40 (1½"): 16 bar (232 psi)
DN 50 (2"): 10 bar (145 psi)

Promass O:

16 bar (232 psi)

Promass X:

Type approved, maximum allowable pressure according to ASME BPVC: 6 bar (87 psi)

Pressure-temperature
ratings

The material load diagrams (pressure-temperature diagrams) for the process connections
are provided in the separate "Technical Information" document on the device in question.
This can be downloaded as a PDF file from www.endress.com. A list of the "Technical
Information" documents available is provided in the "Documentation" section

Rupture disk

To increase the level of safety, a device version with a rupture disk with a triggering pressure
of 10 to 15 bar (145 to 217.5 psi) (Promass X: 5,5 to 6,5 bar (80 to 94 psi)) can be used.

«
...
131
132
133
134
135
...
»

Содержание HART Proline Promass 83





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HART Proline Promass 83

Бренд: Panasonic Страницы: 180

Clavinova CVP-805

Бренд: Yamaha Страницы: 112

Clavinova CLP-270

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 3

Бренд: Samsara Страницы: 16

Бренд: Aqualytic Страницы: 130

Бренд: PCE Instruments Страницы: 6

Бренд: Chauvin Arnoux Страницы: 64

1101-3121-0049-800

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Ocean Reef Страницы: 24

Бренд: Xsensor Страницы: 13

Бренд: RAM Страницы: 43

Бренд: ScienTECH Страницы: 43

Бренд: Allen Organ Company Страницы: 29

Бренд: Biobase Страницы: 36

Бренд: Peavey Страницы: 24

Бренд: Stabila Страницы: 14

Бренд: Komshine Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды