Endress+Hauser Hart Micropilot FMR60B Скачать руководство пользователя страница 9

Страница: 9 / 84

Micropilot FMR60B HART

Basic safety instructions

Hauser

Danger of burns from contact with surfaces!

‣

For elevated fluid temperatures, ensure protection against contact to prevent burns.

2.3

Workplace safety

When working on and with the device:

‣

Wear the required personal protective equipment according to federal/national

regulations.

‣

Switch off the supply voltage before connecting the device.

2.4

Operational safety

Risk of injury!

‣

Operate the device only if it is in proper technical condition, free from errors and faults.

‣

The operator is responsible for the interference-free operation of the device.

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers:

‣

If modifications are nevertheless required, consult with the manufacturer.

Repair

To ensure continued operational safety and reliability:

‣

Carry out repairs on the device only if they are expressly permitted.

‣

Observe federal/national regulations pertaining to the repair of an electrical device.

‣

Use only original spare parts and accessories from the manufacturer.

Hazardous area

To eliminate danger to persons or the installation when the device is used in the

hazardous area (e.g. explosion protection, pressure vessel safety):

‣

Check the nameplate to verify whether the ordered device can be put to its intended

use in the hazardous area.

‣

Observe the specifications in the separate supplementary documentation, which is an

integral part of this manual.

2.5

Product safety

This device is designed in accordance with good engineering practice to meet state-of-the-

art safety requirements, has been tested, and left the factory in a condition in which it is

safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC

directives listed in the device-specific EC Declaration of Conformity. Hauser

confirms this by affixing the CE mark to the device.

2.6

Functional Safety SIL (optional)

The Functional Safety Manual must be strictly observed for devices that are used in

functional safety applications.

2.7

IT security

We only provide a warranty if the device is installed and used as described in the

Operating Instructions. The device is equipped with security mechanisms to protect it

against any inadvertent changes to the device settings. IT security measures in line with

Содержание Hart Micropilot FMR60B





















































































Результаты поиска

Содержание Hart Micropilot FMR60B

Отзывы:

Похожие инструкции для Hart Micropilot FMR60B

Бренды по названию

Популярные бренды

Endress+Hauser Hart Micropilot FMR60B, Руководство по эксплуатации

Результаты поиска

Содержание Hart Micropilot FMR60B

Отзывы:

Похожие инструкции для Hart Micropilot FMR60B

Бренды по названию

Популярные бренды