Endress+Hauser Dosimag Скачать руководство пользователя страница 26

Страница: 26 / 76

Electrical connection

Dosimag

Hauser

7.1.4

Requirements for the supply unit

Supply voltage

DC 24 V (nominal voltage: DC 20 to 30 V)

• The power unit must be tested to ensure that it meets safety requirements (e.g.

PELV, SELV).

• The supply voltage must not exceed a maximum short-circuit current of 50 A.

7.2

Connecting the measuring device

NOTICE

Limitation of electrical safety due to incorrect connection!

‣

Have electrical connection work carried out by correspondingly trained specialists only.

‣

Observe applicable federal/national installation codes and regulations.

‣

Comply with local workplace safety regulations.

7.2.1

Connecting the transmitter

Connection by means of device plug

Connection is solely by means of device plug.

A0023685

Coupling

Plug

Grounding

Grounding is by means of a cable socket.

A0003838

7.3

Ensuring the degree of protection

The measuring device fulfills all the requirements for IP67 degree of protection, Type 4X

enclosure.

To guarantee IP67 degree of protection, Type 4X enclosure, carry out the following steps

after the electrical connection:

Содержание Dosimag













































































Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды

Endress+Hauser Dosimag, Руководство по эксплуатации

Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды