Endress+Hauser Deltapilot S FMB70 Скачать руководство пользователя страница 10

Страница: 10 / 36

Deltapilot S

Hauser

Device configuration

Methods for device
configuration

When using the devices in process control protection equipment, the device configuration must meet two
requirements:

Confirmation concept:
proven independent checking of the safety-related parameters input

Locking concept:
device locked after configuration (required in accordance with IEC 61511-1 §11.6.4 and NE 79 §3)

The following methods for device configuration are available:

Standard device configuration

Increased security during parameter entry

Note!
Due to the increased configuration safety, the use of the "Increased security during parameter entry"
method is recommended when using the device in process control protection functions.

Procedure for "Standard device configuration"

Point

➀

"Standard device configuration" section,

→

26, and for the "Level" operating

mode, "Level Easy Pressure" level
selection, also observe the permitted
parameter settings,

→

12 ff.

Point

➁

Observe the prescribed parameters in
accordance with the form,

→

("Pressure" operating mode) and

→

35 ("Level" operating mode,

"Level Easy Pressure" level selection).

SD213en04

Standard device

(manual parameter confirmation and locking)

configuration

Read out the prescribed

parameters

and compare

them to the protocol.

Is the configuration

identical to the

protocol?

Lock the device for safe

measuring mode via software

and/or hardware.

Perform a reset

(code "7864")

The correct display of the

characters and digits is checked

via the DIGITS SET parameter.

yes

Configure the device

(see Operating Instructions

BA332P and BA274P)

and make a protocol of the

settings manually

Read out the

CONFIG RECORDER

parameter and document it.

Содержание Deltapilot S FMB70





































Результаты поиска

Содержание Deltapilot S FMB70

Отзывы:

Похожие инструкции для Deltapilot S FMB70

Бренды по названию

Популярные бренды

Endress+Hauser Deltapilot S FMB70, Руководство по функциональной безопасности

Результаты поиска

Содержание Deltapilot S FMB70

Отзывы:

Похожие инструкции для Deltapilot S FMB70

Бренды по названию

Популярные бренды