Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 59

Страница: 59 / 156

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

PRESS. ENG. UNIT (060)
Selection

Select pressure unit.
If a new pressure unit is selected, all pressure-specific parameters are converted and
displayed with the new unit.

Options:

• mbar, bar
• mmH2O, mH2O, inH2O, ftH2O

• Pa, hPa, kPa, MPa
• psi
• mmHg, inHg

• Torr
• g/cm

, kg/cm

• lb/ft

• atm
• gf/cm

, kgf/cm

• User unit,



See also the following parameter description for CUSTOMER UNIT P and

CUST. UNIT FACT. P.

1) The conversion factor of the pressure units refers to a reference temperature of 4 °C
(39.2 °F).
2) The conversion factor of the pressure units refers to a reference temperature of 0 °C
(32 °F).

Factory setting:

Depends on the sensor nominal measuring range mbar or bar or as per order
specifications

CUSTOMER UNIT P (075)
Entry

Enter text (unit) for customer-specific pressure unit.
You can enter a maximum of eight alphanumeric characters here.



Содержание Deltabar S PMD70





























































































































































Результаты поиска

Содержание Deltabar S PMD70

Отзывы:

Похожие инструкции для Deltabar S PMD70

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar S PMD70, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar S PMD70

Отзывы:

Похожие инструкции для Deltabar S PMD70

Бренды по названию

Популярные бренды