Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 127

Страница: 127 / 156

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

127

HistoROM CONTROL (832)
Selection

For selecting the direction for copying the data.



See also Operating Instructions BA00270P (Deltabar S), BA00271P (Cerabar S) or

BA00332P (Deltapilot S), Section 5.5. "HistoROM

/M-DAT (optional)".

Prerequisite:

• A HistoROM

/M-DAT is attached to the electronic insert

(HistoROM AVAIL. = yes)

Options:

• Abort
• HistoROM



Device

• Device



HistoROM

Factory setting:

Abort (if HistoROM

/M-DAT is connected to the electronic insert)

Table 32: (GROUP SELECTION



) OPERATING MENU



DIAGNOSTICS



SIMULATION

Parameter name

Description

SIMULATION MODE (413)
Selection

Switch on simulation and select simulation type.
Any simulation running is switched off if the measuring mode or level type is changed.

Options

• None
• Pressure,



see also this table parameter description for SIM. PRESSURE

• Flow (only differential pressure transmitter),



Содержание Deltabar S PMD70





























































































































































Результаты поиска

Содержание Deltabar S PMD70

Отзывы:

Похожие инструкции для Deltabar S PMD70

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar S PMD70, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar S PMD70

Отзывы:

Похожие инструкции для Deltabar S PMD70

Бренды по названию

Популярные бренды